Open the tab “CAN data”:

In the field “Method of calculation”, select the parameter based on which Omnicomm Online software will record the CAN parameter.

CAN parameters and possible Method of calculations:

• CAN parameter SPN70. This Method of calculation is set up if the third-party terminal transmits the parking brake status from the bus CAN signal SPN70;

• CAN parameter SPN91. This Method of calculation is set up if the third-party terminal transmits the accelerometer pedal position from the bus CAN signal SPN91;

• CAN parameter SPN100. This Method of calculation is set up if the third-party terminal transmits the engine oil pressure value from the bus CAN signal SPN100;

• CAN parameter SPN110. This Method of calculation is set up if the third-party terminal transmits the coolant temperature value from the bus CAN signal SPN110;

• CAN parameter SPN174. This Method of calculation is set up if the third-party terminal transmits the fuel temperature value from the bus CAN signal SPN174;

• CAN parameter SPN175. This Method of calculation is set up if the third-party terminal transmits the engine oil temperature value from the bus CAN signal SPN175;

• CAN parameter SPN182. This Method of calculation is set up if the third-party terminal transmits the daily fuel consumption value from the bus CAN signal SPN182;

• CAN parameter SPN184. This Method of calculation is set up if the third-party terminal transmits the event of instantaneous fuel economy from the bus CAN signal SPN184;

• CAN parameter SPN190. This Method of calculation is set up if the third-party terminal transmits the engine RPM value from the bus CAN signal SPN190;

• CAN parameter SPN244. This Method of calculation is set up if the third-party terminal transmits the daily mileage value from the bus CAN signal SPN244;

• CAN parameter SPN245. This Method of calculation is set up if the third-party terminal transmits the total mileage value from the bus CAN signal SPN245;

• CAN parameter SPN247. This Method of calculation is set up if the third-party terminal transmits the value of the total time of engine operation from the bus CAN signal SPN247;

• CAN parameter SPN250. This Method of calculation is set up if the third-party terminal transmits the total fuel consumption from the bus CAN signal SPN250;

• CAN parameter SPN521. This Method of calculation is set up if the third-party terminal transmits information about the service brake pedal position from the bus CAN signal SPN521;

• CAN parameter SPN522. This Method of calculation is set up if the third-party terminal transmits information about clutch pedal position from the bus CAN signal SPN522;

• CAN parameter SPN527. This Method of calculation is set up if the third-party terminal transmits the cruise control status from the bus CAN signal SPN527;

• CAN parameter SPN582. This Method of calculation is set up if the third-party terminal transmits the axle pressure value from the bus CAN signal SPN582;

• CAN parameter SPN597. This Method of calculation is set up if the third-party terminal transmits information about the service brake pedal status from the bus CAN signal SPN597;

• CAN parameter SPN598. This Method of calculation is set up if the third-party terminal transmits information about the clutch pedal status from the bus CAN signal SPN598;

• CAN parameter SPN914. This Method of calculation is set up if the third-party terminal transmits data about the mileage until the next maintenance from the bus CAN signal SPN914;

• CAN parameter SPN916. This Method of calculation is set up if the third-party terminal transmits data about the Engine run time until the next technical maintenance from the bus CAN signal SPN916;

• CAN parameter SPN928. This Method of calculation is set up if the third-party terminal transmits data with the axle index from the bus CAN signal SPN928;

• CAN parameter SPN1624. This Method of calculation is set up if the third-party terminal transmits the VH instantaneous speed value from the bus CAN signal SPN1624;

• CAN parameter SPN1821. This Method of calculation is set up if the third-party terminal transmits information about the VH door status from the bus CAN signal SPN1821;

• CAN parameter SPN1856. This Method of calculation is set up if the third-party terminal transmits information about the VH seatbelt status from the bus CAN signal SPN1856.