Report “Log” allows review of “raw” data received by Omnicomm Online from the terminals.

1. Select a VH.

2. Please select a period of time for report generation.

Select information to be displayed in the report by pressing the right mouse button and choosing “Report settings”:

Report contains the following information on the selected vehicle:

The “General” section:

•Date and time is date and time of the event.

•Ignition is a state of ignition at the certain moment (On or Off).

•GPRS is presence or absence of GPRS at the given moment.

•GPS is presence or absence of data from GPS at the given moment.

•Number of satellites is a number of satellites based on which GPS data were determined at the given moment.

•Coordinates are coordinates (latitude and longitude) of the vehicle location at the given moment, measured in degrees or message “Connection of on-board equipment” at the moment of connection of the terminal with the Communicaton server. If the number of satellites for coordinates determination is less than 4, coordinates are displayed grey.

•Direction is direction of vehicle motion (N (North); NE (Northeast); E (East); SE (Southeast); S (South); SW (Southwest); W (West); NE (Northwest)).

•Height, (m) is altitude of the VH above the sea level.

•Mileage, (km) is path travelled by the car.

•Speed GPS, (km/h) is VH speed at the given moment determined by GPS.

•Speed pulse is a value of speed in kilometers per hour by the data from the regular meter or read from the CAN-bus depending on the speed imput settings on Omnicomm online software.

•Acceleration (m/s2) is a value of VH acceleration.

•Revolutions means level of revolutions per minute by data from tachometer or read from the CAN-bus depending from the settings on Omnicomm Configurator software.

•ON voltage is voltage of VH onboard network (V). For Omnicomm Profi in case of operation from reserve battery, voltage of reserve battery (RB).

•Data on CAN-bus.

•Values from four universal inputs.

•LLS1, LLS2, LLS3, LLS4, LLS5, LLS6 is code from the first to the sixth by LLS fuel level sensor. If there is no calibration table for this sensor, “0” is displayed grey.

•T (LLS1), T (LLS2), T (LLS3), T (LLS4), T (LLS5), T (LLS6) is temperature (C°) output from the first to the sixth sensor of LLS fuel level sensor. If there is no calibration table for the sensor, “0” is displayed grey.

•LLS1 status, LLS2 status, LLS3 status, LLS4 status, LLS5 status, LLS6 status:

— Ready, the sensor is connected and shows correct data

— No, the sensor is not connected or adaptive data collection in the Terminal is on

— Error, the sensor is connected, but shows incorrect data

— Not ready, the sensor is ready, but power supply to the sensor started less than 15 seconds ago

•“Volume of fuel dispensing”, (l) (for fuel tanker only) is volume of fuel dispensed through fuel nozzle.

•“The source of event” is condition for creation of an event by the Terminal (turning point, timer)

The “CAN parameters” section:

•Parking brake status

•Accelerator pedal position, %

•Engine oil pressure, kPa

•Engine coolant temperature, °C

•Fuel temperature, °C

•Engine oil temperature, °C

•Daily fuel consumption, l

•Instantaneous fuel economy, km/l

•Engine rpm

•Daily mileage, km

•Total mileage, km

•Total time of engine operation, h

•Overall fuel consumption, l

•Position of the service brake pedal

•Clutch pedal position

•Cruise Control status

•Axle load, kg

•Status of the service brake pedal

•Status of the clutch pedal

•Mileage before the next maintenance, km

•Engine operation time before the next

•Maintenance, h Instantaneous speed, km/h

•Doors status

•Seatbelts status

•CAN rpm

•OBDII. Mileage after error reset, km

•OBDII. Time after error reset, h

•OBDII. Fuel level, %

•OBDII. VIN ТС

•OBDII. Check Engine error

The “iQFreeze” section:

•CHU temperature

•Refrigerator temperature in section 2

•Refrigerator temperature in section 3

•Set temperature

•Set temperature 2

•Set temperature 3

•Ambient temperature

•Coolant temperature

•Engine rpm

•Compressor configuration

•System status

•Door status

•Battery voltage

•Battery current

•Operating hours from the engine

•Operating hours from the onboard network

•Unit serial number

•Trailer serial number

•Number of errors

•Code of the main error

•2nd, 3rd, 4th, 5th, 6th level errors

•IQFreeze serial number

•IQFreeze firmware version

•IQFreeze Bluetooth name

•Unit type

•Connection to CHU

•Digital inputs No.1, No.2

The “Tire Pressure Monitoring” section:

•Wheel number: current pressure, kPa

•Wheel number: current temperature

•Wheel number: wheel sensor connection status

•Wheel number: sensor battery charge

•Wheel number: reason for sending. Possible values: recurrent sending, air leakage, rapid air leakage, tire re-inflated

The “Safe Driving” section:

•Violation source

•Speed threshold, km/h

•RPM threshold, rpm

•Acceleration threshold, m/s2

•Lateral acceleration threshold, m/s2

•Braking acceleration threshold, m/s2

•Vertical acceleration threshold, m/s2

•Acceleration along the X-axis, m/s2

•Acceleration along the Y-axis, m/s2

•Acceleration along the Z-axis, m/s2

•Accelerometer status

The “GenComm generators” section:

•Oil pressure, kPa

•Coolant temperature, °C

•Voltage of the charging generator, V

•Frequency of the output voltage, Hz

•L1, L2, L3 voltage, V

•L1-L2, L2-L3, L1-L3 line voltages, V

•L1, L2, L3 currents, A

•L1, L2, L3 active power, W

•L1, L2, L3 total powers, kVA

•L1, L2, L3 reactive power, kVAr

•Power factor

•Motor hours

•Total energy generated, kW⋅h

•Fuel volume, %

•Charge current, A

•Battery voltage, V

•Revolutions, rpm

•Diesel status

•Status of the diesel-driven generator set

Optional parameters:

•FLS PMP-201, Struna+

The “Display of technological operation parameters” section:

“Type of equipment” - select the type of equipment for which to display technological parameters.

Possible options: TG series Grader and WX200, TX210 Excavator.

For the TG series Grader the following parameters are displayed:

•ICE. Coolant temperature, °C

•ICE. Charge air temperature, °C

•ICE. Oil pressure, bar

•ICE. Charge air pressure, bar

•ICE. Crankshaft rotation speed, rpm

•Gearbox. Oil pressure in the lubrication system, bar

•Gearbox. Oil pressure in torque converter, bar

•Gearbox. Error codes

•Gearbox. Oil temperature

•Gearbox. Speed, km/h

•Gearbox. Number of the current gear

•Gearbox. Operating mode

•Electrical system. Voltage, V

•ICE. Oil temperature, °C

•ICE. Fuel rail pressure, bar

•ICE. Error codes

•Hydraulic system. Oil temperature, °C

•Hydraulic system. Oil pressure, bar

To change the width of a column, select the border of the column and drag it while holding the left button of the mouse.

Display parameters as a diagram

1. Select a column with a parameter

2. Right-click and select “Display as a diagram”

When a point is selected on the graph, the corresponding row in the “Log” report is automatically highlighted.

Hiding rows with parameter values that are equal to zero or missing

1. Select a column that contains rows with valid and missing parameter values.

2. Right-click and select “Hide rows with empty cells”

3. Rows with missing values will be hidden in the report. To show rows again, right-click and select “Reset all filters”.

Let's take the column with the parameter “Revolutions” as an example.

To hide the empty cells:

After the empty cells have been hidden:

Parameters for which the option of hiding rows does not apply:

•Row number

•Date and time

•Ignition key position

•GSM connection

•GPS data validity

•Digital output status

•Event source

•Sensor level code

•Sensor temperature

•Sensor readiness

•Coordinates

•GPS speed

•Pulse speed

•Dispensed fuel volume

•Power

•Battery charge percentage

•Direction

•Number of satellites

•Height

•Mileage

•UI1…UI4